The NOR Gate That Got Us To The Moon

Type G micrologic
The Fairchild Type ‘G’ Micrologic gate for the Apollo Guidance Computer – this is the flat pack verison

In a previous post I talked about how the going to the moon kick started the silicon age. If you haven’t read it, it is short but really interesting story about how NASA made Integrated circuits cheap, and partially funded what we now know as Silicon Valley. In this post I am going to take a slightly closer look at the circuit that ran the famous type “G” Micrologic gate that ran the Apollo Guidance Computer.

apollo 3 input NOR gate
The official NASA schematic of the Type G micrologic gate found in the Apollo Guidance Computer

As you can see in the above image, the circuit was not particularly complicated. You have to remember that this is very early logic, before CMOS or NMOS or any other fancy IC technologies. This is basically two 3 input NOR gates, they both run off the same power, with pin 10 at the top, and the negative which was likely ground being shared on pin 5. The output for the left NOR gate is pin 1, and the output for the right is pin 9. The three inputs for the left are pins 4, 2 and 3, with the right having pins 6, 7, and 8 as inputs. Simply put, the output is “pulled” high to power when all the inputs are OFF. The resistor between pin 10 and pin 1 (or 10 and 9) are a simple pull up resistor as you would find in most electronic circuits. As expected with a NOR gate, the output will be only be ON when all the inputs are OFF. When any of the inputs are ON the output of that gate will be pulled to ground. One two, or all the inputs can be on, but it just needs one to turn OFF the output. The resistors going into the base of the transistor are just to limit the current.

3 input NOR
My breadboarded version of the 3 input NOR gate, it is made with BC547 transistors and a DIP switch. the output has been inverted with the LED.

I made a simple recreation of this circuit using BC547 NPN transistors, but most NPN transistors would work, these were ones I found in my parts box. As you can see in the image above, I have made it on a breadboard, with the inputs being a DIP switch attached to the power (5V in this case). The base resistors for the transistors are 1K and the pull-up to 5V is a 10K. I recommend making up this circuit if you want to learn a bit more about logic, and is a cheaper method than going out to buy 74 series logic chips! As you can see in the images there are a number of states that I showed the circuit in, and notice that if any of the switches are on, the circuit turns on, this is slightly against what I mentioned earlier, but thats due to the output LED using the transistor as a current sink, not a source, so the output is inverted. Basically, when the output is 0 the LED turns on. The only time the LED is off (output high) is when no switches are on, meaning all the transistors are off.

apollo 3 input NOR gate
An image of the silicon die inside the Type G 3 input NOR gate. We will be going through how the layout works in a future post.

The final point for this post is why the circuit is actually quite efficient. Modern logic is amazingly low power compared to this. One of the biggest issues is that it is always taking power in some way. When the inputs are off, there is still some leakage through the pull up resistor, when an input is on, then there is current going through the resistor to ground. Also, by the nature of the transistors there is always parasitic leakages, and inefficiencies in the process. They are only small numbers, but the AGC used over 3000 of these circuits, so the small leakages soon add up to draw some hefty power needs, especially for battery powered operations.

If you enjoyed this post, take a look at the rest of my blog, there is lots about space, electronics and random history. I am always open to ideas and feedback, and where is best to post links to my posts.

Leave a Reply

Your email address will not be published. Required fields are marked *